G360 Super Fast Compound

G360 Super Fast Compound can be used to eliminate 3000 grit sanding and polish rapidly from P1500 to a deep gloss finish:

HIGH CUT - To eliminate P1500 sanding marks from conventional low bake clear coats and prepare the surface for MEDIUM CUT polishing, use:

Rotary - G360 Super Fast Compound with a G Mop Super High Cut Pad [RED]
Dual Action - G360 Super Fast Compound with a G Mop Super High Cut Pad [WHITE] 

MEDIUM CUT - To remove process marks, rapidly eliminate heavier swirls and holograms and leave an excellent gloss finish on light colours while preparing dark colours for FINE CUT polishing, use:

Rotary & Dual Action - G360 Super Fast Compound with a G Mop Angled Yellow Compounding Foam

See our dedicated Solution pages for full details - including handling instructions and recommended speeds:

How to Use: G360 Super Fast Compound
Process Guide: G360 Super Fast System for ROTARY Polishers
Process Guide: G360 Super Fast System for DUAL ACTION Polishers

1. Don’t overapply – use between 30% and 50% less compound than you would normally use with other brands. Use sparingly – too much incurs additional and unnecessary cost, extra clean up time, and can clog the pad reducing effectiveness of cut.
2. For optimum performance in removing P1500 sanding scratches always use the Super High Cut Pad. This reduces the need to use P3000 which reduces cost and cycle time.
3. When using a rotary polisher ensure the machine speed is set to the correct level between 1500 and 1800 RPM – too low or too fast will result in low product performance and increase polishing cycle time.
4. Apply light pad pressure. Don’t lean on the polisher or hold it at too steep an angle – it might sometimes cut quicker, but holograms and therefore reworks can result.
5. Don’t polish for too long – this can put micro-scratches into the surfaces, which then take more time to get out. Using products that have a transparent film can help.
6. Knead a brand new foam before first use and prime it with compound – this stops any initial “scratchiness” and prompts more effective polishing at the outset.
7. Always spur foam and wool polishing pads regularly. Wash them out with warm water and leave to dry overnight to prolong the life of pads. A build-up of compound from previous jobs will reduce cut and cause skating. Dried compound can put scratches into the surface.
8. Avoid polishing under-cured paint (paying particular attention to the baking oven panel bake temperature and cold spots, gun set-ups, spraying technique. Soft paint cannot be polished effectively and may require reworking at a later stage.
9. Always use two microfibre cloths (dirty and clean) – learn the folding technique for always using a clean section of microfibre to avoid marring the finished surface.
10. Finally, good housekeeping is paramount to a successful outcome. Ensure all machinery is in a well maintained and clean state ensure all pads are washed and spurred regularly.

G360 Super Fast Compound is designed to quickly remove P1500 sanding marks from automotive paint surfaces, eliminating the need to use P3000 sanding discs, speeding up the defect removal process in bodyshops.

G360 Super Fast Compound is Farécla's flagship automotive liquid compound, specifically designed to reduce the need for sanding with P3000 discs. It offers our fastest defect removal on painted and lacquered automotive surfaces.

For optimal results, particularly on darker colours, it’s recommended to follow on with G360 Super Fast Finish after using G360 Super Fast Compound.

No, G360 Super Fast Compound does not contain any fillers. The results it delivers are permanent, and you can confirm this by degreasing the surface after polishing. The finish remains flawless, showing that no temporary fillers are masking any defects.

A Rotary polisher spins in a continuous circular motion, creating a direct and aggressive polishing action that is ideal for faster defect removal and heavier cutting applications.

A Dual Action (DA) polisher combines rotary and oscillating movements, producing a smoother and generally less aggressive polishing action that is commonly used for refining and finishing.

Although Rotary polishing will typically deliver a heavier cut, actual polishing performance depends on a range of factors including substrate type and condition, compound and applicator selection, machine speed, user handling and machine throw. In some spot repair situations, smaller orbit Dual Action machines such as the G Plus Mini Dual Action Polisher may achieve both rapid correction and a high finishing performance when head to head against its rotary counterpart.

Several G Mop applicators can be used across both Rotary and Dual Action polishing systems. Users should check product packaging and the product listings for compatibility guidance and recommended operating instructions.

Both machine types are capable of achieving high quality correction and finishing results in skilled hands. The choice between Rotary and Dual Action polishing often depends on the application, substrate condition, working area and operator preference.

Many Farécla process guides and solutions are designed around a preferred machine type. However, users with access to both Rotary and Dual Action polishers may mix and match recommended processes and product combinations according to operator preference and application requirements to achieve optimal results.

Yes. G360 Super Fast Compound can be used with both Rotary and Dual Action polishing systems when paired with the correct applicator and process.

Farécla currently offers two versions of the G Mop Super High Cut Pad designed for use with G360 Super Fast Compound:

• Red | GMC650 - Rotary use ONLY
• White | GMC660 & GMC760 - Dual Action use ONLY

See: What is the difference between the "RED" and "WHITE" G Mop Super High Cut Pads? for full details

When used with a Dual Action machine and the recommended applicators, G360 Super Fast Compound is capable of delivering strong correction and a high gloss finish as either a standalone process or as part of a wider polishing system.

See: Process Guide: G360 Super Fast System for DUAL ACTION Polishers for full details

Broadly speaking, Rotary polishing systems will typically deliver the fastest and most consistent higher correction performance with G360, particularly during heavier correction applications. However, some users may prefer Dual Action polishing for improved finishing characteristics, increased control or personal preference.

For users looking for a Dual Action-focused alternative, G3 Pro D.A. Cutting Compound is also recommended. Developed primarily with enthusiast and detailing users in mind, it is compatible with the recommended pads used within the G360 Dual Action process and offers a lower dusting polishing experience while still delivering strong correction performance.

Both the Rotary and Dual Action G360 Super Fast processes are designed to deliver rapid defect removal and a high gloss finish, but they differ in machine action and recommended applicators for certain stages of the process.

HIGH CUT - To remove P1500 or finer sanding marks
This stage eliminates P1500 sanding marks from conventional low bake clear coats and prepares the surface for MEDIUM CUT polishing.

• Rotary - G360 Super Fast Compound with a G Mop Super High Cut Pad [RED]
• Dual Action - G360 Super Fast Compound with a G Mop Super High Cut Pad [WHITE] 

While similar in appearance, subtle differences in dimensions, foam structure and the fibres of the polishing face mean they behave differently in use. As a result, each pad requires a specific handling approach for optimal control and to avoid introducing additional surface defects.

MEDIUM CUT - To remove process marks and medium defects such as swirls and light scuffs
This stage rapidly eliminates heavier swirls and holograms, leaving an excellent gloss finish on light colours while preparing dark colours for FINE CUT polishing.

• Rotary & Dual Action - G360 Super Fast Compound with a G Mop Angled Yellow Compounding Foam

FINE CUT - To remove fine defects such as holograms and light swirls while enhancing gloss levels
This stage further enhances gloss levels on light colours while rapidly eliminating light swirls and holograms on dark colours for an enhanced deep gloss finish.

• Rotary - G360 Super Fast Finish with a G Mop Angled Black Finishing Foam
• Dual Action - G360 Super Fast Finish with a G Mop Dual Action Finishing Foam

The recommended finishing pads for Rotary and Dual Action polishing are designed to offer optimal handling, machine stability and airflow characteristics for their respective machine actions.

Broadly speaking, Rotary polishing is commonly favoured for fast and consistent higher correction performance, while Dual Action polishing is often preferred for increased control and enhanced finishing characteristics.

The choice between Rotary and Dual Action polishing will depend on operator preference, substrate condition, working area and the finish standard required. Users with access to both machine types may also combine elements of each process to suit the application and optimise overall performance.

For further details, see:

• Process Guide: G360 Super Fast System for ROTARY Polishers
• Process Guide: G360 Super Fast System for DUAL ACTION Polishers
• What is the difference between the "RED" and "WHITE" G Mop Super High Cut Pads?

Farécla offers two types of G Mop Super High Cut Pad(s):

The RED Pad
150 mm Range: GMC650 (78072700153) 
Introduced alongside G360 Super Fast Compound, this pad is recommended for use with ROTARY polishing processes.

The WHITE Pad
150 mm Range: GMC660 (66254427056)
180 mm Range: GMC760 (66254427057)
Introduced in 2026, this pad is recommended for use with DUAL ACTION polishing processes.

Both pads are designed for use with G360 Super Fast Compound and will remove P1500 or finer sanding scratches when used as part of the correct process.

While similar in appearance, subtle differences in dimensions, foam structure and the fibres of the polishing face mean they behave differently in use. As a result, each pad requires a specific handling approach for optimal control and to avoid introducing additional surface defects.

For best performance, Farécla recommends:
GMC650 – Rotary use ONLY
GMC660 & GMC760 – Dual Action use ONLY

Further guidance is available in the related FAQs: 

• Can GMC650 be used with a DUAL ACTION Polishing Machine?
• Can GMC660 be used with a ROTARY Polishing Machine?

NOTE: Due to an administrative error, some early “new look” packaging (see “G Mop Applicator Range – Packaging Update”) for GMC650 and GMC660 incorrectly suggest cross-use between rotary and dual action polishing machines. Artwork has been updated, and future production runs will carry the revised information