G360 Super Fast Polishing System - Complete Kit

G360 Super Fast Compound can be used to eliminate 3000 grit sanding and polish rapidly from P1500 to a deep gloss finish:

HIGH CUT - To eliminate P1500 sanding marks from conventional low bake clear coats and prepare the surface for MEDIUM CUT polishing, use:

Rotary - G360 Super Fast Compound with a G Mop Super High Cut Pad [RED]
Dual Action - G360 Super Fast Compound with a G Mop Super High Cut Pad [WHITE] 

MEDIUM CUT - To remove process marks, rapidly eliminate heavier swirls and holograms and leave an excellent gloss finish on light colours while preparing dark colours for FINE CUT polishing, use:

Rotary & Dual Action - G360 Super Fast Compound with a G Mop Angled Yellow Compounding Foam

See our dedicated Solution pages for full details - including handling instructions and recommended speeds:

How to Use: G360 Super Fast Compound
Process Guide: G360 Super Fast System for ROTARY Polishers
Process Guide: G360 Super Fast System for DUAL ACTION Polishers

No – on the contrary – the G360 Compound when used with a Super High Cut Pad runs very cool which is excellent for fresh paint but it does have a very high cut which is also really, really good on long cured paints and OEM paints.

G360 Super Fast Finish - used as a follow on from MEDIUM CUT step of G360 Super Fast Compound - can be used to further enhance gloss levels of light colours and on dark colours to rapidly eliminate light swirls and holograms and leave an enhanced deep gloss finish.

FINE CUT - To further enhances gloss levels on light colours while rapidly eliminating light swirls and holograms on dark colours for an enhanced deep gloss finish, use:

Rotary - G360 Super Fast Finish with a G Mop Angled Black Finishing Foam
Dual Action - G360 Super Fast Finish with a G Mop Dual Action Finishing Foam

See our dedicated Solution pages for full details - including handling instructions and recommended speeds:

How to Use: G360 Super Fast Finish
Process Guide: G360 Super Fast System for ROTARY Polishers
Process Guide: G360 Super Fast System for DUAL ACTION Polishers

1. Spray a light mist onto the surface.

2. Use a clean, G Plus Finishing Cloth to immediately wipe off polishing residues, glue lines etc.

3. Using a dry area of the cloth, or ideally a 2nd clean, dry microfibre cloth, buff the surface.

For tougher contamination like birdlime, allow the product to dwell for a few seconds before wiping

If left and dried on the surface – wet with more product

1. Don’t overapply – use between 30% and 50% less compound than you would normally use with other brands. Use sparingly – too much incurs additional and unnecessary cost, extra clean up time, and can clog the pad reducing effectiveness of cut.
2. For optimum performance in removing P1500 sanding scratches always use the Super High Cut Pad. This reduces the need to use P3000 which reduces cost and cycle time.
3. When using a rotary polisher ensure the machine speed is set to the correct level between 1500 and 1800 RPM – too low or too fast will result in low product performance and increase polishing cycle time.
4. Apply light pad pressure. Don’t lean on the polisher or hold it at too steep an angle – it might sometimes cut quicker, but holograms and therefore reworks can result.
5. Don’t polish for too long – this can put micro-scratches into the surfaces, which then take more time to get out. Using products that have a transparent film can help.
6. Knead a brand new foam before first use and prime it with compound – this stops any initial “scratchiness” and prompts more effective polishing at the outset.
7. Always spur foam and wool polishing pads regularly. Wash them out with warm water and leave to dry overnight to prolong the life of pads. A build-up of compound from previous jobs will reduce cut and cause skating. Dried compound can put scratches into the surface.
8. Avoid polishing under-cured paint (paying particular attention to the baking oven panel bake temperature and cold spots, gun set-ups, spraying technique. Soft paint cannot be polished effectively and may require reworking at a later stage.
9. Always use two microfibre cloths (dirty and clean) – learn the folding technique for always using a clean section of microfibre to avoid marring the finished surface.
10. Finally, good housekeeping is paramount to a successful outcome. Ensure all machinery is in a well maintained and clean state ensure all pads are washed and spurred regularly.