Click on image to zoom-in


  • No P3000 Required - permanently removes P1500 sanding marks when used with a G Mop Super High Cut Pad.
  • Super Fast Cut - rapidly and permanently removes process marks such as swirls when used with a G Mop Compounding Foam.
  • Transparent in Use - see the defects being removed
  • Permanent results – No reworks
  • Use on MS / HS / UHS / Scratch Resistant Clears
  • Bodyshop Safe (No Silicones)
Automotive Market

About: G360 Compound

G360 Super Fast Compound is designed to rapidly eliminate sanding marks and minor defects from painted and lacquered automotive surfaces.

When used with a G Mop Super High Cut Pad, the compound glides over the surface and eliminates P1500 sanding marks, cutting rapidly and with little effort - removing the need for P3000 abrasives.

Transparent in use, the operator is able to see these marks disappear permanently.

The compound eliminates all holograms and removes swirl marks when used with a G Mop Angled Compounding Foam.

For darker colours, the operator may wish to follow on with G360 Super Fast Finish.


FPL Part No.
Carton Qty
Carton Barcode
1 kg
6 Bottle(s)
500 g
12 Bottle(s)
100 g
24 Tube(s)

Use With...

G MOP SUPER HIGH CUT PAD - Photo of 2 Red Microfibre Foam Pads - Velour Side and Side On view

The G Mop Super High Cut Pad, developed in conjunction with G360 Super Fast Compound, eliminates P1500 sanding marks and removes the need for costly P3000 sanding discs.

G MOP FLEXIBLE BACK PLATE - Side view of 6 Inch Yellow Back Plate

The G Mop Flexible Back Plate adds additional flexibility to Farécla's range of compounding and finishing foams - allowing for improved handling performance, increased performance and increased pad life. 

Follow On With...

G360 SUPER FAST FINISH - Range Photo of 1 L, 500 ML SKU(s) on a white background

G360 Super Fast Finish is designed to rapidly eliminate swirls and holograms from painted and lacquered automotive surfaces - ideal on darker colours after using G360 Compound.

CLEAN AND PROTECT - Photo of 1L size SKU(s) on a white background

Clean and Protect is an easy to use “wipe on, wipe off” product - rapidly removing contaminants from paint, glass, rubber and plastics, whilst leaving a silicone-free layer of protection to the surface 

FAQs & How to Use

Your Questions Answered - Farécla G360 Super Fast System

How to Use: G360 Super Fast Compound How to Use: G360 Super Fast Compound

G360 Super Fast Compound can be used to eliminate 3000 grit sanding and polish rapidly from P1500 to a deep gloss finish.

To replace sanding with 3000 grit first use a Farécla Super High Cut Pad (GMC650), and then remove process marks created by step 1 using a G Mop Angled Compounding Foam (GMC622).

  1. Ensure surface is clean, dry and cool to the touch
  2. Shake bottle well before use
  3. Apply a small amount of product onto the surface and spread across the defect area
  4. Start at 1500rpm with the Super High Cut Pad at a slight angle, and finish at 900rpm with the pad flat to the surface
  5. Switch pad to the G Mop Angled Compounding Foam
  6. Apply a small amount of product onto the surface
  7. Polish briefly at 900-1300rpm
  8. Wipe clean with a G Plus Finishing Cloth and repeat if necessary
Top 10 tips to boost cost effectiveness with Farécla G360 Top 10 tips to boost cost effectiveness with Farécla G360
  1. Don’t overapply – use between 30% and 50% less compound than you would normally use with other brands. Use sparingly – too much incurs additional and unnecessary cost, extra clean up time, and can clog the pad reducing effectiveness of cut.
  2. For optimum performance in removing P1500 sanding scratches always use the Super High Cut Pad. This reduces the need to use P3000 which reduces cost and cycle time.
  3. When using a rotary polisher ensure the machine speed is set to the correct level between 1500 and 1800 RPM – too low or too fast will result in low product performance and increase polishing cycle time.
  4. Apply light pad pressure. Don’t lean on the polisher or hold it at too steep an angle – it might sometimes cut quicker, but holograms and therefore reworks can result.
  5. Don’t polish for too long – this can put micro-scratches into the surfaces, which then take more time to get out. Using products that have a transparent film can help.
  6. Knead a brand new foam before first use and prime it with compound – this stops any initial “scratchiness” and prompts more effective polishing at the outset.
  7. Always spur foam and wool polishing pads regularly. Wash them out with warm water and leave to dry overnight to prolong the life of pads. A build-up of compound from previous jobs will reduce cut and cause skating. Dried compound can put scratches into the surface.
  8. Avoid polishing under-cured paint (paying particular attention to the baking oven panel bake temperature and cold spots, gun set-ups, spraying technique. Soft paint cannot be polished effectively and may require reworking at a later stage.
  9. Always use two microfibre cloths (dirty and clean) – learn the folding technique for always using a clean section of microfibre to avoid marring the finished surface.
  10. Finally, good housekeeping is paramount to a successful outcome. Ensure all machinery is in a well maintained and clean state ensure all pads are washed and spurred regularly.