Need help? We answer your questions

What are "Peel & Reveal" / "-EX" G3 Pro Variants? What are "Peel & Reveal" / "-EX" G3 Pro Variants?

A number of G3 Pro products have "-EX" versions which are available in select international markets.

These "-EX" SKUs contain identical formulations to their non-EX (UK and English Language Market) counterpart but have a multi-language "Peel & Reveal" label on the front, offering Health and Safety information in 28 different languages.

They share the same FPL Part No* with the addition of an -EX

e.g. 7164 = G3 Pro Scratch Remover Liquid (Label: English Only)
7164-EX = G3 Pro Scratch Remover Liquid (Label: Peel & Reveal with 28 Languages)

* Other elements such as the SGA Code and Barcodes are different.

Some SKUs do not have -EX counterparts as no H&S is required (e.g. 7191 G3 Pro Deep Clean Clay Mitt)

How to Use: G Scuff How to Use: G Scuff

1. Spray a mist of water onto a scuff/abrasive pad or a mutton cloth (pad/cloth not supplied by Farécla)

2. Shake bottle well before use

3. Apply a small amount of product to surface or pad

4. Rub product with abrasive pad or cloth using back and forth motions

5. Wipe clean with a Farécla G Plus Finishing Cloth

Note: It is always recommended to test on an inconspicuous area prior to general use

How to Use: G3 Pro SuperGloss Paste Wax 2.0 How to Use: G3 Pro SuperGloss Paste Wax 2.0

1. Ensure the surface is clean before use and cool to the touch (do not use in direct sunlight)
2. Apply wax to a G3 Pro Black Waffle Applicator Pad
3. Use circular overlapping motions with even pressure, avoiding plastic trims
4. Allow to dry to a haze. Can be left even for an extended period and will still buff off exceptionally easily
5. Gently wipe with a clean, dry microfibre cloth

How to Use: G3 Pro Rapid Detailer 2.0 How to Use: G3 Pro Rapid Detailer 2.0

1. Spray a light mist of product onto the surface

2. Use a Farécla G Plus Finishing Cloth to spread the product and clean the surface, wiping off polishing residues glue, lines etc.

3. Use a dry area of the cloth, or ideally a second, clean dry Farécla G Plus Finishing Cloth to buff the surface

Note: for tougher contamination like birdlime allow the product to dwell for a few seconds before wiping

FOR INGRAINED DIRT

1. Having first washed the surface, spray G3 Pro Rapid Detailer onto both the selected work area and a G3 Pro Deep Clean Clay Mitt

2. Gently work the mitt over the lubricated surface with light pressure without letting it dry. CAUTION: Keep the G3 Pro Deep Clean Clay Mitt lubricated during use

3. Buff off any residue with a soft, clean, dry microfibre cloth using a light circular motion. The surface should now feel smooth to the touch

How to Use: G3 Pro Rapid Detailer How to Use: G3 Pro Rapid Detailer

1. Spray onto a clean, dry Farécla G Plus Finishing Cloth

2. Wipe over small areas at a time

3. Buff off immediately with a clean, dry Farécla G Plus Finishing Cloth 

FOR INGRAINED DIRT

1. Having first washed the surface, spray G3 Pro Rapid Detailer onto both the selected work area and a G3 Pro Deep Clean Clay Mitt

2. Gently work the mitt over the lubricated surface with light pressure without letting it dry. CAUTION: Keep the G3 Pro Deep Clean Clay Mitt lubricated during use

3. Buff off any residue with a soft, clean, dry microfibre cloth using a light circular motion. The surface should now feel smooth to the touch

How to Use: Profile (300) Rapid Cut How to Use: Profile (300) Rapid Cut

1. Attach a G Mop 8” Twisted Wool Compounding Pad to polishing machine

2. Mix product well and apply a small amount to surface

3. Spread and compound at 1800–2000rpm applying medium pressure

4. Wipe clean with a G Plus Finishing Cloth

How to Use: Profile Premium Paste How to Use: Profile Premium Paste

1. Sand area - Profile Premium Paste Compound removes up to P1200 scratch marks

2. Attach a G Mop 8” Single Sided Wool Pad to a polishing machine

3. Mix product well and apply a small quantity of the product to the surface or pad

4. Spread and compound at 1500-1800rpm

5. Wipe clean with a G Plus Finishing Cloth

How to Use: G3 Pro Surface Sanitiser How to Use: G3 Pro Surface Sanitiser

HARD / NON-POROUS SURFACES

1. Spray liberally on the surface until fully saturated (i.e. visibly wet), then spray a small amount on to a clean, dry microfibre cloth

2. Wipe the surface with the cloth until fully covered. Ensure that difficult to reach/unseen areas (such as corners, gaps, channels etc.) are fully contacted

3. Leave the solution in contact with the surface for 5 minutes

4. Use a separate clean, dry microfibre cloth to remove any residue

SOFT / POROUS SURFACES (including fabric and leather)

1. Spray liberally on the surface until fully saturated (i.e. visibly wet)

2. - Wipe/brush the solution in difficult to reach areas (such as corners, gaps, channels etc.) using either a clean, dry microfibre cloth or soft brush

3. Leave the solution in contact with the surface for 5 minutes

4. Use a clean, dry microfibre cloth, soft brush or vacuum to remove residue

How to Use: G10 Finishing Compound How to Use: G10 Finishing Compound

1. Attach a soft finishing foam to a polishing machine

2. Shake bottle well before use

3. Apply a small amount of product to the surface or foam

4. Compound at 1500-1800rpm applying little or no pressure

5. Wipe clean with a G Plus Finishing Cloth

How to Use: G6 Paste How to Use: G6 Paste

MACHINE APPLICATION

1. Soak compounding head or foam in water

2. Attach pad to the polishing machine, spin off excess water and knead

3. Mix compound well and apply to pad or surface

4. Spread and compound at 1500-1800rpm

5. Wipe clean with a G Plus Finishing Cloth

HAND APPLICATION

1. Soak a G Plus Finishing Cloth in water and rinse out

2. Mix compound well and apply to cloth or surface

3. Rub product on the surface in a back and forth motion

4. Wipe clean with a G Plus Finishing Cloth

How to Use: G6 Rapid Liquid How to Use: G6 Rapid Liquid

1. Attach a compounding foam to a polisher and knead

2. Shake bottle well and apply a small amount to surface or foam

3. Spread on surface and compound at 1500–1800rpm until marks have been removed

4. Wipe clean with a G Plus Finishing Cloth

How to Use: G3 Advanced How to Use: G3 Advanced

1. Soak pad in clean water

2. Squeeze out excess water and attach to polishing machine

3. Spin off excess water until there is no over spray from pad

4. Shake well, apply a small amount of product and spread with pad to reduce throw off

5. Compound at 1500-1800rpm until marks have been removed

6. Keep pad damp using clean water from a G Plus Water Spray Bottle

7. If necessary add more compound to completely remove the marks

8. Wipe clean with a G Plus Finishing Cloth
 

How to Use: G3 Flexicut How to Use: G3 Flexicut

1. Attach a G Mop Wool Pad to a polishing machine

2. Mix well before use and apply a small amount to the pad or surface

3. Compound at 1500 - 1800rpm

4. Wipe clean with G Plus Finishing Cloth

How to Use: G3 Pro Super Dressing How to Use: G3 Pro Super Dressing

1. Spray sparingly onto the surface or a clean, dry microfibre cloth

2. Wipe on to clean, then buff off with a clean, dry microfibre cloth to leave a natural, ‘as new look’ finish

3. Further applications will build the gloss level if a high shine finish is desired

How to Use: G3 Pro Glass Cleaner How to Use: G3 Pro Glass Cleaner

1. Lightly mist onto all windows, wing mirrors and indicators
2. Gently wipe clean with a clean, dry microfibre cloth
3. Turn the cloth over and buff to a finish